Why does the viscosity, or the thickness, of an industrial liquid affect its flow rate? It has to do with the creation of the internal friction of the liquid and its relation to surface tension.
What type of spray equipment do you need? You can choose from airless, electrostatic, air spray, airless air-assisted, high volume low pressure (hvlp) or lvlp (low volume high pressure). Let us know what it will be used for and we'll supply the right equipment.
Never use a new nut with on old bolt or an old nut with a new bolt. Heat, age, and tension will cause the older product to deteriorate below its safety threshold, creating an unstable and unsafe joint. Always replace both with new ones at the same time.
When working with certain materials it’s always safe to double check what adhesives you should use with the materials you are using. Some adhesives, even if they are tough and dependable, could eat through a substance, so you should opt for a water based adhesive if that is the case.
One quick way to determine if a given part is causing a problem is to swap it with an identical one. If the problem goes away, get rid of the old one. If there's still a problem, put it back and keep working through your checklist.
Before you order shelving for vertical storage, make sure you have the correct lifting equipment. It must be able to reach above the top level and safely support the weight of the load.
Did you know that duct tape was invented for a military purpose? It replaced paper tabs on ammunition packages that kept breaking off when they got wet, making it difficult for soldiers to open the packages during combat situations.
Because the primary function of an alternator is to create electrical energy by converting mechanical energy, the diodes need to be in good condition or it will not function properly. While replacement diodes are available, in most cases the replacing the alternator is the better option.
A quality lubricant is a cost-saver. When the correct formulation is used, equipment is less likely to break because of a lubricant-related issue, resulting in reduced costs for upkeep, maintenance, repair labor, and revenue lost because equipment is out of commission.
For many industrial applications, aluminum is a primary material. It is lightweight, resists corrosion, and can be welded, cast-forged, and machined easily. It is also available in a number of high-performing alloys.
The use of adhesives dates as far back as a human could discover, so far back it has been dated to be from 200,000 years ago. The very first use of adhesives lied in Italy, as two stones were stuck with tar, and this is also believed to be the very first axe.
For many external applications, there are four classifications of hydraulic pumps. From least to most expensive they are: gear, vane, piston, and variable volume. If you are not sure what you have or which you need, our team will be glad to help.
Did you know that building and construction is one of the largest markets for adhesives? Just some of the areas they are used in include laying carpet, roofing, flooring, laminating drywall, HVAC, and wall coverings.
Bearings made from chrome steel alloys provide noise dampening for quieter operation – important if noise is a concern. However, this material corrodes at a faster rate than stainless steel, so the operating environment needs to be taken into consideration.
It is the rpm of the shaft and the load that determines the voltage output of a permanent magnet alternator. As the rpm increase, so does the voltage. Conversely, as the load increases, the voltage drops.
Hydraulic systems work with compressed liquids, usually specially formulated oils, while pneumatic systems work with compressed air. The pipes, hoses, filters and other parts are not interchangeable and the entire system will fail if the wrong ones are used.
For multiple materials operations, combination drums are available that are rated for both dry and liquid materials. They are leak proof, seal tightly and carry two sets of UN markings to indicate their multi-purpose construction.
Keep the acronym STAMPED in mind when ordering hoses: Size, Temperature, Application, Material, Pressure, Ends, and Delivery. By addressing each of these, you cover all aspects of hoses for any application.
If your systems rely on fans for cooling, don't neglect them as failure will cause overheating and a complete shutdown. If you notice erratic performance, it's time to replace the part.
Fiberglass insulating jackets and boards can be used for pipes, ducts, boilers, stack, tanks, and power installations. With a working temperature range from 0°F to 1000°F, they perform across multiple industries.
Quick couplings are available that can attach hoses to the machine, to additional hoses, and to nozzle holders. Different materials and configurations are available to fit any system and application.
Barrels and drums used for storing and shipping hazardous materials must have a UN rating. The rating doesn't refer to manufacturing characteristics, but provides information on the type of drum or barrel and what standards it meets.
Deciding on the correct grade of stainless steel depends on a number of factors, including chemical concentration, atmospheric conditions, operational temperature, presence of water, performance expectations, and more.
Many times parts will provide clues that they are about to fail. Odd sounds, unusual odors, and spotty performance are all indicators that it is time to replace a part. Don’t wait until the last minute.