HANSA-FLEX SUPPORTS AMUSEMENT PARKS IN ITS MAINTENANCE WORK FOR FUN AND SAFETY.
At 213 feet the Volcano Tower is not quite as high as the viewing platform, but it offers a very special ride experience: passengers are catapulted to the top of the tower at more than 34 mph and then plummet down again. Two large pneumatic aggregates accelerate and gently brake the gondola, which is suspended on two steel cables. The ride lasts just under two and a half minutes. The four pressure accumulators must then be refilled. The entire system is controlled by a technically trained operator with years of experience. “For the acceleration it’s important for the cylinder to operate at the right pressure,” explains Gröll. “This depends on the total weight of all the passengers, which is calculated by load cells installed in the seats and varies between 160 and 218 PSI”
“We completely dismantled the Vulcano Tower last year using a 160-ton crane,” says Gröll “This year we also replaced all the hose lines and overhauled the brake cylinders.”A comprehensive task, in which HANSA-FLEX was happy to support. An absolute highlight: the test runs. These enable the operators to become familiar with the ride characteristics and are a duty that is gladly performed after every maintenance operation.
#hoseandfitting #hydraulics #fluidpower #hansaflexusa #hansaflex #metric #hydraulicequipment
#GIVEAWAY ALERT 🚨 Head over to our Hansa-Flex USA #LinkedIn page to submit an entry for a free T-Shirt!
Winners will be randomly selected on September 1st, 2020 and reach out to the winners via LinkedIn.
Thanks to Mark Paxton and Michael Szafron for being the models for these custom-designed shirts!
A couple Hansa-Flex tools that make life easier for mechanics, technicians, salespeople, and engineers alike. Slide charts and calipers are a necessary component for hose building and fitting identification. 👍🏼
#hoseandfitting #hydraulics #fluidpower #hansaflexusa #hansaflex #metric #hydraulicequipment
Mark Paxton, the CEO of HANSA-FLEX USA, visited Henderson Rigs & Equipment last week. Almost every rig had at least a few of our products as original equipment! 👍🏼
#hoseandfitting #hydraulics #fluidpower #hansaflexusa #hansaflex #metric #hydraulicequipment
We hope you have a great last day of July! This year is going by fast, isn’t it? ☀️
#hoseandfitting #hydraulics #fluidpower #hansaflexusa #hansaflex #metric #hydraulicequipment
Working on some valve conversions for our customer. 👍🏼 How are you being productive this Monday morning?
#hoseandfitting #hydraulics #fluidpower #hansaflexusa #hansaflex #metric #hydraulicequipment
When projects arise that require some extra thinking, HANSA-FLEX USA rises to the challenge! Our customer needed a specific #metric size on each port and angled in the proper direction, which raised a small challenge. Teal Bagwell was able to successfully identify the appropriate #adapters in order to create this final product.
We will always put forth our best effort to produce a quality product that fits our customer's needs! That's the Hansa-Flex promise.
Ever been through a tunnel of hose assemblies?
#hoseandfitting #hydraulics #fluidpower #hansaflexusa #hansaflex #metric #hydraulicequipment
Do you recognize #metric adapters when you see them?
Often it can be a pain to identify #fitting types, especially metric if you're unfamiliar.
👍 That's where we step in. 👍
Hansa-Flex has the right personnel and tools for the job, and we can typically identify your mystery fitting within minutes! Metric is our specialty!
#hydraulics #hydraulicsystems #hoseandfittings #adapters
On Thursday, 22 October, building owner Thorsten Armerding and board member Uwe Buschmann, together with representatives of the Jürgen Schlake architectural office and the construction company responsible, BREMER AG, symbolically broke the ground to mark the start of construction work on the expansion of Bremen headquarters. It will be the largest construction project in the history of HANSA-FLEX.
Congratulations to HANSA-FLEX AG for their upcoming expansion! We can't wait to celebrate it's arrival from afar.
Product Showcase: Metric Tubing
We have a large variety of tubing sizes in carbon and stainless steel, from 4MM to 60MM and with wall thickness measurements from 1-5. We’re also able to cut the tubing if needed for ease of transportation!
Contact your local Hansa-Flex branch to get a competitive quote today!
#hoseandfitting #hydraulics #fluidpower #hansaflexusa #hansaflex #metric #hydraulicequipment
We provide engineering, design/redesign for fluid power systems so that everything flows smoothly, without cavitation. This photo shows what turbulent flow across an orifice can do to an aluminum manifold if cavitation occurs outside of the needle valve cartridge. Optimizing a fluid power system can save thousands per year in fuel, greenhouse gas emissions, and maintenance, while in increasing performance.
#hoseandfitting #hydraulics #fluidpower #hansaflexusa #hansaflex #metric #hydraulicequipment
Let's hope for a better year than the last! With more opportunities, happier moments, and loving connections that get us through each day.
Cheers to 2021 🎉
#hoseandfitting #hydraulics #fluidpower #hansaflexusa #hansaflex #metric #hydraulicequipment #happynewyear
Holiday hours updated for all Hansa-Flex USA branches. We hope you have a safe and wonderful season!