The term “bearings” of ball bearings is used because these parts bear and reduce rotational friction when supporting axial and radial loads. This gives them a lower friction coefficient than that of flat surfaces performing the same operations.
When storing lumber, pipe or other long inventory, open cantilever racks are a good option. Their general configuration allows for easy storage and removal of materials either by hand or forklift.
Hot melt adhesives are designed to be melted and applied in a liquid state. When the heat source is removed and the adhesive cures, the cooled adhesive forms a strong bond that effectively bridges gaps.
Barrels and drums used for storing and shipping hazardous materials must have a UN rating. The rating doesn't refer to manufacturing characteristics, but provides information on the type of drum or barrel and what standards it meets.
The first use of liquid adhesive took place in 2,000 B.C. The ancient Egyptians used it in attaching wood in various works of art. It was made from animal products.
Never use a new nut with on old bolt or an old nut with a new bolt. Heat, age, and tension will cause the older product to deteriorate below its safety threshold, creating an unstable and unsafe joint. Always replace both with new ones at the same time.
If the supplies being ordered are being used in the food industry, let us know. We'll supply you with lubricants that comply with FDA and local regulations. This includes the animal feed industry as well.
Did you know that the spiral configuration inside certain pump casings is called a volute? It is so named because it resembles the spiral arrangement found inside the shells of mollusks called Volutidae. Ammonites are the ancient ancestors of these creatures.
Will you be expanding your business in the near future? If so, talk with us about the equipment and supplies you anticipate you will need so you can move forward as soon as you are ready.
When you, or your staff, use industrial cleaning supplies, personal protective gear (PPG) is needed. Long pants, shoes with good traction, gloves, and safety glasses or goggles and hearing protectors are needed when handling chemicals and cleaning equipment.
Choosing the right industrial adhesive can significantly increase productivity. Some new adhesives are formulated to cure best on uncoated metal surfaces, which can reduce the need for prepping parts with primer.
It is the rpm of the shaft and the load that determines the voltage output of a permanent magnet alternator. As the rpm increase, so does the voltage. Conversely, as the load increases, the voltage drops.
When ordering chemical-based cleaners you're not familiar with, schedule a training seminar for all who will be handling them. This creates a safer work environment and a standard protocol that prevents misinformation and misapplication.
Bearings made from chrome steel alloys provide noise dampening for quieter operation – important if noise is a concern. However, this material corrodes at a faster rate than stainless steel, so the operating environment needs to be taken into consideration.
Check the energy output of your pump; if more than 25 percent of it is being used to overcome friction, you may want to consider increasing the size of the pipes to reduce it.
Compressors that require oiling may release tiny amounts of aspirated oil into the air and onto the work surface during use. Before using this type of air compressor, make sure the surface cannot be discolored or damaged from the oil mist.
For many external applications, there are four classifications of hydraulic pumps. From least to most expensive they are: gear, vane, piston, and variable volume. If you are not sure what you have or which you need, our team will be glad to help.
A quality lubricant is a cost-saver. When the correct formulation is used, equipment is less likely to break because of a lubricant-related issue, resulting in reduced costs for upkeep, maintenance, repair labor, and revenue lost because equipment is out of commission.
Because the primary function of the alternator is to create electrical energy by converting mechanical energy, the diodes need to be in good condition or it will not function properly. While replacement diodes are available, in most cases replacing the alternator is the better option.
One way to prevent galling (aka cold welding) of stainless steel bolts in sheet metal applications is to use a lower RPM when tightening bolts. This is because higher RPM generate excessive heat, which causes the bolts to seize.
What type of spray equipment do you need? You can choose from airless, electrostatic, air spray, airless air-assisted, high volume low pressure (hvlp) or lvlp (low volume high pressure). Let us know what it will be used for and we'll supply the right equipment.
Keep the acronym STAMPED in mind when ordering hoses: Size, Temperature, Application, Material, Pressure, Ends, and Delivery. By addressing each of these, you cover all aspects of hoses for any application.
Make sure all fittings on industrial pumps are airtight. Look for, and replace, seals that leak and hoses that are damaged or badly worn. Also check the suction flap valves periodically for wear and replace them if needed.
The larger the variable frequency drive, the more heat it generates, creating a greater demand for efficient cooling. If the unit is shutting down because of overheating, the cooling system needs to be updated.