If a self-priming pump isn’t re-priming at the proper rate, check for leaking seals, worn volute cutwater sections, clogging at the re-circulating port, and proper tightening of all hardware at the gaskets.
It’s recommended that you have your pump motor performance evaluated regularly to ensure continued operation of your well. This type of service should include checking the amp load, grounding, and line voltage.
Circular pump casings are either designed as solid or split casings, and are used primarily for multi-stage pumps. This type of casing has stationary diffusion vanes that surround the impeller periphery, effectively converting speed into pressure energy.
If your water well consistently produced inadequate water pressure, there are certain things that can be done in order to boost its performance. One option is to install a well pump pressure booster to give the pump cycle an extra boost.
Adding well pumps to your water well comes with a variety of benefits. It protects the water from contamination. It also assists with irrigation and holds a command on water pressure depending on the type of pump you are using.
Is your home’s well several hundred feet deep? The best way to pump up the water through a submersible pump that pushes the water up the well.
Perhaps the first civilization to use percussion drilling for wells was the ancient Chinese. They used the method to drill wells up that were thousands of feet deep.
If you use a water pump in a decorative fishpond, you will be able to increase the number of fish you keep. Pumps keep the water circulating, improving the health of the fish and any aquatic plants that you have.
If you lose water in your home, one thing you can do to troubleshoot is to check the breaker that supplies power to your pump. If the breaker trips continually, there is either a short in the wiring or the pump is worn out.
Did you know that centrifugal pumps work better when the fluid that they are moving is thicker? In fact, in this type of pump design, the efficiency of fluid movement is increased with an increase of fluid density or thickness.
If your water pump isn’t getting enough suction, this might be caused by air leaks on the intake side of the pump. Air can actually cause cavitations to the pump, creating the loss of suction, and the pipe and/or joints may need to be replaced.
Wells are certainly a huge part of your property, and that means that you shouldn’t discount the fact that there are things that you need to maintain when you have one. The right professional can ensure you know just what is needed.
If you notice that your soap is hard to work into a lather and that there are spots on your faucets, then chances are your well water is hard. To fix this, a water softening system will be needed.
Centrifugal pumps that are end suction, single-stage and constructed according to the American National Standards Institute (ANSI) B73.1 requirements for this type of pump are generically referred to as ANSI pumps. The B73.1 is the most widely accepted standard for pump quality.
If you don't have handy access to your well pump manual, it's a good idea to contact the manufacturer for a duplicate. Operating manuals are a valuable source of maintenance information, regardless of whether your well pump is acting up right now.
Four forms of energy are components of industrial pump systems: pressure, velocity, elevation, and friction. Each describes or explains the movement of liquids within the system.
Why does ice float in water if it is made of water? Water expands by 9% when it freezes, so ice is lighter than water.
In pump operations, the rate of flow at a certain head is called the duty point. Basically, the pump performance curve is going to be made up of many duty points, which helps to determine the overall pump operating point.
Sometimes submersible pumps are used for home wells. These pumps are long and cylindrical, and fit inside the well casing. The bottom half is composed of a sealed pump motor connected to the aboveground power source and controlled by wires, and the other half is composed of a stacked series of impellers that drive the water up.
The term head is a measurement of the kinetic energy that pumping systems create. The main reason to use this measurement is because different liquids will have different pressures, but the head will not change.
To have your pump water evaluated by a certified testing lab, call the health department. Your local health department office will be able to provide a list of certified labs to choose from. Perform a browser search for local or statewide "government offices."
The performance of your pump system will depend greatly on how much fluid the pump is moving and the pressure it’s creating as a result. Essentially, as the flow (or fluid movement) increases, the pressure decreases.
